依客思国标LED防爆灯圆形仓库厂房车间化 工厂加油站50w-300wEKS210

LED防爆灯方形纯铝外壳防水防尘防爆灯具防爆平台灯工厂加油站灯
防爆灯仓库灯车间码头加油站灯三防隔爆投光灯100瓦led防爆灯现货
 
 
 
一、EKS210防爆LED灯适用范围及用途
EKS210防爆LED灯适用于II类（除煤矿以外其它爆炸性气体环境用电设备）含有温度组别为T1-T6的IIA、IIB、IIC级气体或蒸汽爆炸性环境的1区、2区危险场所及可燃性粉尘环境21区、22区危险场所；
在交流50Hz、额定电压220V线路中，作室内／外场所的照明之用。
 
二:EKS210防爆LED灯产品型号含义
J:带应急功能（不注不带）
X:吸顶式：Z:支架式
B:壁式（Bx:弯杆＋吸盘）（Bh:弯杆＋接线盒）
G:吊杆式（Gx:直杆＋吸盘）（Gh:直杆＋接线盒）
H:护栏式
F:法兰式
 
三、EKS210防爆LED灯执行标准
GB 3836.1-2021 爆炸性环境第1部分：设备通用要求；
GB 3836.1-2021 爆炸性环境第2部分：由隔爆外壳＊d”保护的设备；
GB 12476.1-2013 可燃性粉尘环境用电气设备第1部分：通用要求；
GB 12476.5-2013 可燃性粉尘环境用电气设备第5部分：外壳保护型“tD*;
 
四、EKS210防爆LED灯正常使用条件
a)周围空气温度：－40℃-+45℃;
b)标准大气压力80kPa(0.8bar)-110kPa(1.1bar),正常的含氧量21%v/v;
c)安装地点海拔不超过2000米；
d)周围空气相对湿度不大于95%;
e)含有温度组别为T1-T6的IIA,IIB、IIC级气体或蒸汽的爆炸性环境的1区、2区危险场所及可燃性粉尘环境21区、22区危险场所；
f)无显著摇动和颠簸的场所；
g)无破坏绝缘气体或蒸汽的场所；
h)污染街级：3级；
i)安装类别：II类。
 
五、EKS210防爆LED灯产品特点
a)散热器采用特殊铸铝合金压铸而成，表面高压静电喷塑；
b)高防腐性能的不锈钢外露紧固件；
c)止口隔爆结合面，纯隔爆结构，防爆性能更可靠；
d)设计的配光系统，光利用率高，配光合理，照度均匀；
e)高强度物理钢化玻璃，抗冲击及热剧变能力强，透光率高；
f)标准一体式结构设计，具有体积小、散热性能好等特点；
g)安装维护非常方便、快捷、安全；
 
First, the scope and use of EKS210 explosion-proof LED lamp
EKS210 explosion-proof LED lamp is suitable for Class II (other explosive gas environment electrical equipment except coal mine) containing temperature group T1-T6 IIA, IIB, IIC class gas or steam explosive environment of zone 1, Zone 2 dangerous places and combustible dust environment of zone 21, zone 22 dangerous places;
In AC 50Hz, rated voltage 220V line, used for indoor/outdoor lighting.
 
Two :EKS210 explosion-proof LED lamp product model meaning
J: With emergency function (do not note without)
X: Ceiling type: Z: scaffolding type
B: Wall type (Bx: bent rod + suction cup) (Bh: bent rod + junction box)
G: Boom type (Gx: Straight rod + suction cup) (Gh: straight rod + junction box)
H: Guardrail type
F: Flange type
 
Third, EKS210 explosion-proof LED lamp implementation standards
- Explosive atmospheres - Part 1: General requirements for equipment;
- Explosive atmospheres - Part 2: Equipment protected by flameproof housing * d ";
Electrical equipment for use in combustible dust environments - Part 1: General requirements
Electrical equipment for use in combustible dust environments - Part 5: Enclosure protection type "tD*";
 
Four, EKS210 explosion-proof LED light normal use conditions
a) Ambient air temperature: -40℃-+45℃;
b) The standard atmospheric pressure is 80kPa(0.8bar)-110kPa(1.1bar), and the normal oxygen content is 21%v/v;
c) The elevation of the installation site shall not exceed 2000 meters;
d) The relative humidity of the surrounding air is not more than 95%;
e) Hazardous places in Zone 1 and Zone 2 containing explosive environment of IIA,IIB, IIC class gases or vapors of temperature group T1-T6, and hazardous places in Zone 21 and Zone 22 of combustible dust environment;
f) where there is no significant shaking or jolting;
g) a place free from damaging insulating gas or steam;
h) Pollution street level: Level 3;
i) Installation category: Class II.
 
Five, EKS210 explosion-proof LED lamp product features
a) The radiator is made of special cast aluminum alloy die-casting, with high voltage electrostatic spray on the surface;
b) Exposed stainless steel fasteners with high anti-corrosion properties;
c) stop flameproof joint surface, pure flameproof structure, explosion-proof performance is more reliable;
d) Professionally designed light distribution system, high light utilization, reasonable light distribution, uniform illumination;
e) High strength physical tempered glass, strong impact and thermal shock resistance, high light transmittance;
f) Standard integrated structure design, with small volume, good heat dissipation performance;
g) Installation and maintenance is very convenient, fast and safe;